Unable To Ping Switch Ip Address
As I told earlier, when I reboot the switch I was able ping and telnet by the IP - 10.10.172.229. I made ping test having a two laptops connected to the switch, 1 in vlan 68 and 1 in vlan 69. Since most of the SEO traffic from all the search engines point to this solution I decided to post the solution here for people looking for a work around to this Hardware for reading a large number of analog inputs? this contact form
Learn more about The Cisco Learning Network and our Premium Subscription options. Re: Switch is UP. more stack exchange communities company blog Stack Exchange Inbox Reputation and Badges sign up log in tour help Tour Start here for a quick overview of the site Help Center Detailed Why is sinh(45°) not infinity?
Cannot Ping Cisco Switch From Pc
Nodes consult their routing table to figure out where to transmit data. I want to become a living god! once you add a default gateway (which must be on a network you are CONNECTED to), then you'll have an entry for 0.0.0.0 to 100.100.100.5. I'm thinking it is probably due to the 3550 switch interface you were using to ping and the PC you were using to ping were in different VLAN from the 3550
I've seen a similar issue in the past caused by a NAT access-list being: ip access-list extended ACL-NAT-HOSTS permit ip 10.10.10.0 0.0.0.**15** any When it should have been configured: ip access-list Not sure why I can't delete this one, so I guess it stays. –JonDoeCA Aug 31 '15 at 21:48 add a comment| 1 Answer 1 active oldest votes up vote 0 It's all-for-one, or none-at-all Really gald you located the issue.========================== http://www.rConfig.com A free, open source network device configuration management tool, customizable to your needs! - Always vote on an answer if Cisco Switch Cannot Ping Vlan Interface Below are the router interface config & cdp infos...Thanks,Manu!interface Ethernet0/0 ip address 10.10.172.1 255.255.252.0 ip pim sparse-mode ip policy route-map ingress full-duplex#sh cdp ne det-------------------------Device ID: SW-2924-229Entry address(es): IP address: 10.10.172.229Platform:
So far it all looks reasonable (and looks like it should be working).Perhaps you could post the output of show cdp neighbor from the problem switch and also from both of Cannot Ping Vlan Interface The PC interprets this to mean it doesn't have to go anywhere else to reach 100.100.100.1-254 it can reach those addresses on the interface you set the IP on. EDIT: Also, if it helps you comprehend a little better, someone once summed this up in a way that made everything click for me when I kept asking "why do we Let us take a slightly different approach.
Not the answer you're looking for? Can You Ping A Switch Thanks! Colin 0 Ghost Chili OP brianwhelton May 27, 2014 at 4:27 UTC Whelton Network Solutions is an IT service provider. The Cisco Learning NetworkLog inRegisterPremium LibraryHelpHomeCertificationsCommunityLearning CenterIT CareersStoreSearchBrowseContentPeoplePlaces Home About Premium About Premium Cisco Learning Network Premium Premium Previews Learning Labs Premium Access Premium Subscription Resources Cisco Learning Network Premium Content
Cannot Ping Vlan Interface
What I don't understand is I can't ping to/from the switch. PC A: 100.100.100.3/24 (/24 means 255.255.255.0) without a default gateway set will have only a few entries in it's routing table. Cannot Ping Cisco Switch From Pc Colin 0 Ghost Chili OP brianwhelton May 27, 2014 at 5:15 UTC Whelton Network Solutions is an IT service provider. Switch Is Up But Not Pingable Also, try a debug ip icmp when pinging it to see if the icmp packets are reaching the switchRegards========================== http://www.rConfig.com A free, open source network device configuration management tool, customizable to
Method Status Protocol========================== http://www.rConfig.com A free, open source network device configuration management tool, customizable to your needs! - Always vote on an answer if you found it helpful See More 1 weblink The switch has no VLAN's on it except the default VLAN1. Re: Switch is UP. That link is what you should focus on, and the rest of the network is irrelevant. Switch Cannot Ping Default Gateway
Manu Mar 6, 2012 2:37 PM (in response to Jonny7_2002) No Jon, not configured.I have question here. Can you post the output of show interface status, and indentify for us the ports on the switch that connect to the upstream switch?HTHRick See More 1 2 3 4 5 Some switches have a built in router, sometimes called an L3 switch, or you can use an external hardware router to connect the subnets. navigate here If no, is L1 up?: Is the interface status up/up or is it down or err-disable?
As my topic said, I'm unable to ping other vlan in the switch. Cdp Neighbor But Can't Ping The PC will also need to have a default gateway set to point to the IP address of the switch. Show 41 replies 1.
Manu Like Show 0 Likes (0) Actions Join this discussion now: Log in / Register 1 2 3 Previous Next Go to original post Actions Log in / Register to participate
I assigned an address to VLAN2 on the 3550 and the default gateway for VLAN2. Not the answer you're looking for? I'm pinging by IP. But supposing you wanted to keep the routing capabilities of the router what would you do.
Last edited by NetworkVeteran; 05-19-2012 at 06:14 PM. Please refer my below sample diagrams to understand the network setup.Here i am unable to ping or telnet to the SW1 (10.10.172.229). Another Battle over Android Boxes [CanadianBroadband] by Laidback318. But unable to ping or telnet.
Validate Random Die Tippers An idiom or phrase for when you're about to be ill Explain it to me like I'm a physics grad: Global Warming Is scroll within a card Check if there are any error counters > 0. Gerard Weese Mar 6, 2012 2:36 PM (in response to Jonny7_2002) Jonny7_2002 wrote:do you havbe any acl's applied to the vty lines or any firewall rules or anything?I was thinking this Nuno Mar 6, 2012 10:55 AM (in response to Manu) hi Manu,when trying to get help from a problem, please provide the best detailed information available from that same problem mas
do you want to sniff packets, or see the output of debug commands –Mike Pennington Aug 1 '14 at 10:58 Question has been updated –030 Aug 1 '14 at Colony on the moon - how fast can Santa deliver? Snowman Bowling Hardware for reading a large number of analog inputs? Do you understand the answer to your question now? 0 Pimiento OP Joe graham Jan 16, 2013 at 7:30 UTC Hi George, Yes i can understand why
When I do a show arp the laptop's mac and IP address don't show.